10 995 kr
- +
CTS 1 Meg solid shaft audio pot - 1 Meg ohm audio taper potentiometer CTS, solid shaft, with hardware.
115 kr
- +
small 16mm. 250K audio potentiometer, 10mm. bushing, M7x0,75 thread Value: Typically 250K pots are used for single coil pickups and 500K pots for humbucker pickups. The bigger the resistence value, the brighter the sound will be/ less highs will bleed off. 1MEG can be used to make humbuckers sound brighter. Taper: The taper of a pot refers to the way its resistance changes as the shaft is rotated. A linear taper pot will work in a linear way related to shaft rotation. As the human ear is not linear in response to increasing volume an audio or logarithmic pot will work best for volume applications. Shaft: A split, knurled shaft will hold most knobs. Sometimes the knob is mounted using a set screw. You should order a solid shaft pot, or align the set screw with the split for correct mounting. Bushing: The standard bushing diameter is 3/8" or 9,5mm, used in most made in USA guitars. Another industry standard is M8, as used by guitar builders outside of the USA. When space is limited mini pots are used with a shaft diameter of 7mm. The standard bushing length is .375" for inch type pots and 10mm for metric type pots. Using two nuts it is very easy to set the correct bushing length for knob placement. Specially for pickguard (ST, PB) or control plate mount (TE, JB) the .250" short bushing will fit perfectly using only one nut. For use with a thick or carved top (LP USA) you should order a bushing length of .750". CTS is (and has been since the 50's) a factory standard for most USA brands like Fender and Gibson. Alpha is a good alternative, nowadays used as a factory standard by Ibanez, Epiphone and Squier.
60 kr
- +
small 16mm. 250K linear potentiometer, 10mm. bushing, M7x0,75 thread Value: Typically 250K pots are used for single coil pickups and 500K pots for humbucker pickups. The bigger the resistence value, the brighter the sound will be/ less highs will bleed off. 1MEG can be used to make humbuckers sound brighter. Taper: The taper of a pot refers to the way its resistance changes as the shaft is rotated. A linear taper pot will work in a linear way related to shaft rotation. As the human ear is not linear in response to increasing volume an audio or logarithmic pot will work best for volume applications. Shaft: A split, knurled shaft will hold most knobs. Sometimes the knob is mounted using a set screw. You should order a solid shaft pot, or align the set screw with the split for correct mounting. Bushing: The standard bushing diameter is 3/8" or 9,5mm, used in most made in USA guitars. Another industry standard is M8, as used by guitar builders outside of the USA. When space is limited mini pots are used with a shaft diameter of 7mm. The standard bushing length is .375" for inch type pots and 10mm for metric type pots. Using two nuts it is very easy to set the correct bushing length for knob placement. Specially for pickguard (ST, PB) or control plate mount (TE, JB) the .250" short bushing will fit perfectly using only one nut. For use with a thick or carved top (LP USA) you should order a bushing length of .750". CTS is (and has been since the 50's) a factory standard for most USA brands like Fender and Gibson. Alpha is a good alternative, nowadays used as a factory standard by Ibanez, Epiphone and Squier.
60 kr
- +
29 kr
- +
Dual-function audio taper pots pull up to activate an on/on double-pole double-throw mini switch. - Can be used as a normal volume or tone control, or control pickup phasing, series/parallel switching, coil-taps, and more. - - 500K-ohm,long shaft pot for Les Paul® - Shaft diameter 6mm split shaft, coarse knurling - Thread 3/8 x 32 - Threaded portion height 3/4" (19.05mm) - Required mounting hole diameter 3/8" (9.52mm) - Required body cavity depth 1-1/8" (28.58mm) - Two mounting nuts, flat washer and lock washer included - - 250K vs. 500K Generally, 500K-ohm pots are used with humbuckers and 250Ks are used with single-coil pickups. You can use any value you like, but a 250K will give a slightly warmer tone than a 500K pot. The 250K pot bleeds off some of the high frequencies to ground. A 1 Meg-ohm pot bleeds off even less than a 500K pot, so if you want to hear your guitar "wide open" you may want to try one. - 1-meg pots are also ideal for piezo pickups, as the ultra high impedance piezo element is more adversely effected by conventional, lower-value pots than magnetic pickups.
229 kr
- +
push-pull 500K audio potentiometer, standard length bushing .375", 3/8" diameter
185 kr
- +
ALTAMIRA N 100 E Med Fishman pickupsystem m/tuner og balansert utgang
5 595 kr
- +
ALTAMIRA N 100 Topp: Hel Seder Sarg/Bunn: Mahogany med lønn som kantlist Hals: Mahogni Gripebrett: Rosentre Hardware: Krom
2 995 kr
- +
Disse gitarene er svært gode, og til en levelig pris. De har usedvanlig god dybde, masse volum og en varm, full tone med herlig klarhet. En av våre gitarlærer-kunder, som også anbefaler dem til sine studenter sier: "En rekke andre gitarlærere spilte på Alhambras, men de ble blåst bort av Altimira. De er fantastiske til prisen! Jeg kunne ikke tro lydene jeg hørte fra et slikt beskjedent priset instrument. " Lokk: Heltre Gran / Seder Sarg/Bunn: Laminert Mahogni Hals: Mahogny Gripebrett: Rosentre Sadel/nut: Bein Finish: High Polish
4 495 kr
- +
Jackplate for Les Paul®, Gold plated, with Screws. Jack hole diameter is 3/8" (9.5mm). 1-11/32" square, with the mounting screw holes spacing - 1" (25.4mm). The jackplate has a slight curve to match the body
105 kr
- +
Jackplate for Les Paul®, Black Plastic. Jack hole diameter is 3/8" (9.5mm). 1-11/32" square, with the mounting screw holes spacing - 1" (25.4mm).
42 kr
- +
Jackplate for Les Paul®, Cream plastic. Jack hole diameter is 3/8" (9.5mm). 1-11/32" square, with the mounting screw holes spacing - 1" (25.4mm).
42 kr
- +
Bass String Guide Round with Screw, Nickel
40 kr
- +
Switchcraft 1/4 inch mono input jack. Includes nut and washer.
45 kr
- +
250K Mini Pot, Audio Taper, 3/8" Long Bushing, Split, Knurled Shaft with Nut and Washer
98 kr
- +
CTS 500K Split Shaft Audio Pot - 500K Audio Pot, CTS, split, knurled shaft with nut, lock and dress washer. Threaded bushing is 3/8" tall
98 kr
- +
Brass Sleeves - Convert Split Shaft Pot to Solid Shaft Pot
10 kr
- +
9-volt battery terminals mounted on rigid plastic
26 kr
- +
On-On Slide Switch by Switchcraft, for Jazzmaster® and Jaguar® guitars. Black Knob, with screws. Requires 3/4" cavity depth and 5/16" x 9/16" slot . 1-1/8" screw spacing
69 kr
- +
250K push / pull audio taper potentiometer. Threaded portion is approximately 9.35 mm diameter. 35mm from bottom of pot to top of threaded portion. Pulls out 4 mm. Includes nut and washer.
200 kr
- +
260 kr
- +
5-way Oak Grigsby blade switch with stainless steel screws
160 kr
- +
5-way Oak Grigsby super switch, 1 wafer, 2 pole, with stainless steel screws
239 kr
- +
ALLPARTS EP-0686-000 CTS 500K Long Split Shaft Audio Pot - 500K Audio Pot, 3/4 Long Threaded Bushing, CTS, split, knurled shaft with nut, lock and dress washer. Threaded bushing is 3/4" tall. Popular replacement pot for many Gibson® Les Paul® guitars.
115 kr
- +
9-Volt Battery pouch for Acoustic guitars
100 kr
- +
75 kr
- +
250K Audio Pot, 3/4 Long Threaded Bushing, CTS, 24 spline split shaft, with hardware
115 kr
- +
300K Linear Pot, 3/4" Long Threaded Bushing, CTS, Split Shaft, with hardware
119 kr
- +
Pickguard Screws Phillips Head, Nickel, #4 x 1/2"
4 kr
- +
230 kr
- +
50 kr
- +
Plastic washers for guitar tuning keys. Placed between button and housing. Inside diameter 3.75 mm, outside 6.5 mm.
7 kr
- +
Plastic washers for bass guitar tuning keys. Placed between button and housing. Inside diameter 4.5 mm, outside 7 mm.
7 kr
- +
90 kr
- +
95 kr
- +
105 kr
- +
– Stemmeskruer for 12-strengs gitar – Dobbelborrede metallstolper – 125 mm – Plastknapper
375 kr
- +
machine heads for guitar, 3x left+3x right, plastic buttons, double drilled metal shaft
285 kr
- +
bridge pins, plastic, ivory, 5mm pearloid dot
19 kr
- +
bridge pins, plastic, black, 5mm pearloid dot
19 kr
- +
bridge pins, 6-pack, rosewood
330 kr
- +
3 x 3 venstre/høyre Komplett
449 kr
- +
battery holder, vertical type, without screws and connector, for 9V block battery
75 kr
- +
top nut, bone, 55x10x7mm, extra large
175 kr
- +
top nut, bone, shaped, 46(43,5)x9x6mm
130 kr
- +
top nut, bone, shaped, 43x8x6mm
130 kr
- +
150 kr
- +
Mekanikkører i metall av bolt-on typ. 19×20 mm. Levereres i 6-pk
99 kr
- +
capacitor, 0,022 microfarad, tone control, for Stallion model
5 kr
- +
15 kr
- +
15 kr
- +
45 kr
- +
45 kr
- +
toggle switch plate, white with gold imprint
45 kr
- +
Strap buttons, metal, chrome/Nikkel, with screw, v-model, diameter 14mm, 2-pack
80 kr
- +
7 kr
- +
Endpin jack, lodding 6,3mm hun jack, Fast jack plate, krom
158 kr
- +
Endpin jack, lodding 6,3mm hun jack, Fast jack plate, gold
185 kr
- +
bridge pins, 6-pack, rosewood
30 kr
- +